Tools required for application

• Protective tape
• Scissors or cutter
• Sander
• 40-grit sandpaper
• 180-grit sandpaper
• Spatula. Steel trowel
• Microfibre roller
• Paint tray
• Electric mixer
• Vacuum cleaner
• Measuring cup or digital scale

Required CimentArt products

• CimentArt PLUS or STD Primer
• CimentArt fibreglass mesh
• KONCRET BASE flooring + MIX resin or Microcement BASE walls + MIX resin or Aqua BASE 100% waterproof
• MICROSTUCCO microcement
• STD Sealer
• WB two-component polyurethane varnish (water-based) or HARD SB (solvent-based) CIMENTART (Comp A and Comp B).

Before starting

Check the surface where it will be applied and ensure that the surface is:

• Straight
• Firm and stable
• Dry and free of moisture
• Clean
• Free of dust, grease, etc.

Preparation of surfaces

Any floor, uneven or cement wall, tiled walls, shower floors and, in general, any surface that is not completely smooth and perfectly flat needs to be levelled beforehand. To do this, we have three types of BASE microcements for levelling the surface:

• KONCRET BASE (FLOORS): Can be applied to all indoor and outdoor floors, without exception. Two-component product. Mix 4 parts Koncret Base with 1 part Mixing Resin. Coverage: 1.25 kg/m² per 1 mm layer, with 2 layers always required.
• Microcement BASE walls: Applied to walls that need levelling, both indoors and outdoors. Two-component product. Mix 3 parts Microcement BASE walls with 1 part Mixing Resin. Coverage: 1 kg/m² per 1 mm layer, with 2 layers always required.
• Aqua BASE 100% waterproof: Applied to walls that need levelling and shower floors. Interior and exterior. Ready-to-use and 100% waterproof product. To achieve complete colour homogenisation, it is recommended to mix it with an electric mixer. Coverage: 1 kg/m² per 1 mm layer, with 2 layers always required.

Step-by-step application

Apply protective tape where necessary.

For application on completely smooth walls (i.e. walls without joints, imperfections or small rough patches, such as completely smooth, sanded and filled walls or painted plasterboard), only carry out steps 2, 3, 4 and 5 (skip step 1).

For application on floors, walls in poor condition or with tile joints, follow steps 1, 3, 4 and 5 (skip step 2).

1. Cement floors or walls, uneven or with tiles: 

Spread the CimentArt fibreglass MESH and apply a coat of CIMENTART PLUS PRIMER. 

Apply the first coat of any of our Microcemento BASE products.

• Using a steel trowel at a 45° angle, apply a maximum thickness of 0.7 to 1 mm (the thickness is determined by the grain of the mixture and the pressure applied during application).
• Finish the first layer, leaving it as smooth as possible and without irregularities.
• Remove the protective tape before the Microcement BASE hardens.
• Allow the first coat of Microcemento BASE to dry completely.
• Drying time varies depending on humidity, temperature, ventilation, etc.
• Remove any irregularities that may have remained after applying the first coat of Microcemento BASE with a spatula or 40-grit sandpaper.
• Remove any dust created by sanding. You can also wipe with a damp cloth. 
• Apply protective tape where necessary.
• Apply the second coat of Microcemento BASE with a steel trowel, using an angle of 30°  , and applying a maximum thickness of 1 mm (the thickness is determined by the grain of the mixture and the pressure applied during application).
• Finish this second coat, leaving it as smooth as possible and without any irregularities.
• Tip: for both the first and second coats, you can spray lightly with water using a spray diffuser and smooth with the trowel to correct any irregularities. 
• Remove the protective tape before the Microcement BASE hardens and allow the second layer of Microcement BASE to dry completely. 
• Drying time is relative depending on humidity, temperature, ventilation, etc. 
• Sand the second layer of Microcement thoroughly with 40-grit sandpaper, correcting any irregularities until the surface is completely smooth.
• Remove the sanding dust by vacuuming. You can also wipe it with a damp cloth. 
• Apply protective tape where necessary.

2. Completely smooth walls: 

Apply a coat of CimentArt PLUS or STD r CimentArt.

Wash the roller and tray with water.

3. MICROSTUCCO microcement

• The coverage of MICROSTUCCO Microcement is approximately 350-400 g/m² when applying the product in a 0.1 mm layer. Two layers must be applied, requiring a total of 700 to 800 g to cover 1 m².
• Tip: if you are applying MICROSTUCCO Microcement to completely smooth walls, you may need to apply 3 coats to cover the surface.
• The product is supplied ready to use, but it is advisable to mix it well with a spatula or electric mixer until you have a homogeneous mixture of colour.

Application of the first coat of MICROSTUCCO Microcement

• Use a steel trowel with rounded edges, such as those used for stucco.
• Apply in short strokes in layers with a maximum thickness of 0.1 mm.
• The thickness is determined by the grain of the mixture and the pressure applied with the trowel.
• Tip: To achieve maximum hardness, the application must be done with pressure. This pressure can cause marks (darker spots) from the friction of the trowel with the Microcement. If you want to avoid them, apply all layers of MICROSTUCCO Microcement with the CimentArt plastic trowel.
• Finish the first coat, leaving it as smooth as possible and without any irregularities.
• Remove the protective tape. Allow the first layer of MICROSTUCCO Microcement to dry completely.
• Drying time varies depending on humidity, temperature, ventilation, etc.
• Sand the first layer of MICROSTUCCO Microcement with 180-grit sandpaper, correcting any irregularities.
• Remove the dust created by sanding with a vacuum cleaner.
• Tip: before applying the second coat in very hot environments, you can lightly spray the surface with water using a spray bottle. This will help with application.
• Apply protective tape where necessary.

Apply a second coat of MICROSTUCCO Microcement following the same procedure as for the first coat.

• Using a steel trowel, apply in short, circular movements at an angle of 30°, applying a maximum thickness of 0.1 mm (the thickness is determined by the grain of the mixture, applying a certain amount of pressure with the trowel).
• Tip: while applying the second coat, you can lightly spray the applied surface with a spray bottle filled with water and smooth it again with the trowel. This will help you achieve a smoother finish.
• Finish the second coat, leaving it as even as possible and without any irregularities.
• Tip: to ensure that no joints are visible, the final layer of MICROSTUCCO Microcement should be applied continuously without stopping.
• Drying time depends on humidity, temperature, ventilation, etc.
• Tip: to ensure that no joints are visible, the final layer of MICROSTUCCO Microcement should be applied continuously without stopping.

Remove the protective tape and allow the second coat of MICROSTUCCO Microcement to dry completely:

• The drying time is relative depending on humidity, temperature, ventilation, etc.
• Sand the second layer of MICROSTUCCO Microcement with 180-grit sandpaper, correcting any irregularities.
• Remove the dust created by sanding with a vacuum cleaner. Never use a damp cloth at this stage.

4. STD Sealer

• Apply protective tape where necessary.
• Pour the STD Sealer into a tray and apply an even coat with a short-pile roller or microfibre roller.
• The coverage of STD Sealer is 100 g/m². To cover 10 m², you will need 1 kg. 

Wash the roller and tray with soap and water.

• Allow the Sealer to dry. Drying time varies depending on humidity, temperature, ventilation, etc. It usually dries fairly quickly.

5. CimentArt Two-Component Polyurethane Varnish

Water-based 2-component WB varnish

Recommended for: interior and exterior application on all walls and ceilings and on floors with moderate foot traffic.

Preparation:

• Mix 5 parts of Component A of the 2-component water-based varnish with 1 part of Component B.
• To make 1 kilo of varnish with the two components, you will need 840 g of Component A and 160 g of Component B.
• The approximate coverage is 50 g/1 m², applying a thin layer of 0.1 mm. It is always necessary to apply 2 coats. To cover 10 m² with 2 coats, you will need approximately 1 kg of the mixture.

HARD SB solvent-based 2-component varnish

Recommended for: indoor and outdoor application on floors with heavy foot traffic.

Preparation:

• Mix 2 parts of Component A of the 2-component solvent-based varnish with 1 part of Component B.
• To make 1 kg of solvent-based 2-component varnish with the 2 components, you will need 666 g of Component A and 333 g of Component B.
• The approximate coverage is 100 g/m², applying a thin layer of 0.1 mm. It is always necessary to apply 2 coats. To cover 10 m² with one coat, you will need approximately 1 kg of the mixture.
• Apply a first coat of varnish 0.1 mm thick with a microfibre roller or spray gun (combing the surface well if applying with a roller) and leave to dry for at least twelve hours.
• Apply a second coat with a microfibre roller or spray gun, exactly the same as the first coat.
• You can apply an extra third coat for added protection, especially in areas that come into direct contact with water, such as showers, outdoor terraces, etc.
• Do not forget to wash the roller and tray with water or solvent, depending on the type of varnish used.

Important

• MICROSTUCCO Microcement can be applied to any surface, except for surfaces with capillary moisture, swimming pools, car parks and factories with heavy machinery traffic.
• We do not recommend applying MICROSTUCCO Microcement on shower floors or outdoor terraces, as it has a very smooth finish and can be slippery when in contact with water.
• Never apply layers of MICROSTUCCO Microcement with a thickness greater than 0.1 mm.

• Microcemento Fino Traditional, iCem, Oxide or Microstucco CIMENTART should not be used on shower floors or outdoor terraces (horizontal surfaces that receive a large amount of water). For these types of surfaces, we recommend using the AQUA range, which is ready to use and 100% waterproof.
• In high-traffic areas such as shops, offices or shopping centres, etc., we recommend applying a third coat of HARD SB solvent-based 2-component varnish.
• Always apply any of our CimentArt 2-component varnishes in thin layers of 0.1 mm.
• Ensure that the entire microcement surface is perfectly covered with any of our 2-component varnishes.
• We recommend finishing any floor with any of our CimentArt 2-component varnishes with a GLOSS or SATIN finish.
• We do not recommend finishing Microcement with a porous or rustic finish and/or light colours on floors, as they will be more difficult to clean.